HYDRAULIC EXTRUDER
for bicomponent
polysulphide or silicon sealant
model H505B or S505B
HYDRAULIC EXTRUDER
for bicomponent polysulphide or silicon sealant
model H505B or S505B
Automatic machine for metering, mixing and the extrusion of twocomponent sealants for the manufacture of insulating glass.
The extrusion hydraulic system gives to the machine special power characteristics that allow substantial flows of product.
MAIN FEATURES
- Basic extrusion piston pump, driven by a hydraulic cylinder and mounted on lifter with pressing plate for 200 liters drum.
- Piston catalyst feed pump, a pneumatic motor with a lift and pressing plate for 20-liter drums (immersion version available on request).
- Mixing system STAINLESS STEEL CRIOMIX composed by three stages with two propellers (nr.3 propellers for the silicon version), situated immediately ahead of of the extrusion gun.
- Hydraulic pump unit with high pressure silenced pump.
- Adjusting pressure extrusion through hydraulic valve.
- Adjusting the quantity of sealant through oleo-hydraulic regulator.
- Safety against over pressures by pressure switches with digital display.
- LED diagnostic panel on the control panel easy to read.
- Oil cooling system and accumulator for a better extrusion homogeneity.
- Acoustic alarm to signal the beginning of catalization inside the mixer
- Qick wash system with basic product (with very low product’s waste)
- Coated tubes in stainless steel (inside Teflon) (only for silicon extruders)
- Stainless steel valves (only for silicon extruders)
OPTIONS
- AUXILIARY SOLVENT PUMP for circuit washing of blended products.
- FREEZER to preserve the mixed product (only for poysuphide extruders).
- STRAIGHT DISPOSABLE MIXER with stainless steel body and two Teflon propellers length 400 mm (lenght 600 for silicon extruders).
- ELECTRIC HEATER RESISTANCE FOR DRUMS 200 lts.
TECHNICAL FEATURES
- Basic product Capacity: 200 liters
- Catalyst Product Capacity: 20 liters
- Product max capacity: 1.7 kg /min at 20°C
- Volumetric dosage: 100 to 8 100 ÷ 12
- Compressed air pressure: 6 bar
- Electrical power: 5 kW 380 V
three-phase - Maximum height: 3,000 mm
- Maximum length: 1.700 mm
- Maximum depth: 1.300 mm
- Weight: 550 kg
PNEUMATIC EXTRUDER
for bicomponent
polysuphide or silicon sealant
model T705B or S705B
PNEUMATIC EXTRUDER
for bicomponent polysuphide or silicon sealant
model T705B or S705B
Automatic machine for dozing, mixing and extrusion of two components sealants for insulating glass.
The pneumatic extrusion system gives to the extruder the particular characteristics of reliability and ease of use.
This machine works with two components polysulphide or siclicon.
MAIN FEATURES
- Base extrusion piston pump driven by a pneumatic motor placed on a ram lift with follower plate, for 200 liters drums.
- Catalyst feeding piston pump driven by pneumatic air motor and placed on a lift with follower plate, for 20 liters drums.
- Mixing system STAILESS STEEL CRIOMIX composed by three stadiums with two propellers, (nr.3 propellers for the silicon version) located immediately ahead of the extrusion gun.
- Safety feature against overpressure achieved by digital gauges.
- Pressure regulation for the output of the product by using pneumatic valves.
- Acoustic alarm to signal the beginning of catalysis within the mixer.
- Qick wash system with basic product (with very low product’s waste).
- Coated tubes in stainless steel (inside Teflon) (only for silicon extruders).
- Stainless steel valves (only for silicon extruders).
OPTIONS
- AUXILIARY SOLVENT PUMP for circuit washing of blended products.
- FREEZER to preserve the mixed product.
- STRAIGHT DISPOSABLE MIXER with stainless steel body and two Teflon propellers length 400 mm (lenght 600 for silicon extruders).
- ELECTRIC HEATER RESISTANCE FOR DRUMS 200 lt.
TECHNICAL FEATURES
- Base product capacity: 200 liters
- Catalyser product capacity: 20 liters
- Product max extrusion capacity:
1,2 kg/min at 20°C - Compressed air consumption:
Nm 3/h 30 - Compressed air pressure: 8 bar
- Power supply: 1 Ph 220 V
- Power rating: 0,5 KVA
- Frequency: 50 Hz
- Maximum height: 1.600 mm
- Maximum length: 900 mm
- Maximum depth: 2.900 mm
- Weight: 450 kg
PNEUMATIC EXTRUDER
monocomponent
sealants
model S301
PNEUMATIC EXTRUDER
monocomponent sealants
model S301
This machine is built to pump and apply high viscosity monocomponent sealants.
It is mainly employed in the insulating glass industry for sealant applications.
The machine pumps the product directly from the drum in the right proportion and extrudes it through a hose and a gun.
Machine is placed on a base with revolving wheels.
MAIN FEATURES
- Extrusion pump
- High pressure pump
- Pressing plate
- Pneumatic elevator
TECHNICAL FEATURES
- Extrusion pressure: 40-200 bar
- Maximum machine load: 0,31 lt/min
- Power supply pressure: 2-10.3 bar